How To Make F3A 3D Rc Airplane By Diy Rc Plane EP1

How To Make F3A 3D Rc Airplane By Diy Rc Plane EP1
How to make a F3a 3d radio controlled plane with foam and detailed DIY rc plane methods.
how to make Rc airplane model with foam like Flitetest.

✅ Necessary materials and equipment.
Foam Pound 2 inches 1 sheet : https://www.lazada.co.th/tag/foam-board/
Cutter or cutter knife : https://www.ofm.co.th/category/office-supplies/cutting-tools/cutter
foam glue : https://www.b2s.co.th/4026700403596.html
1 sheet of sandpaper : https://www.boonthavorn.com/tools-hardware/tools/power-tools-accessories/sandpapers
1 x Wood Sanding Sandpaper :https://www.boonthavorn.com/tools-hardware/tools/power-tools-accessories/sandpapers
1 ruler : https://www.freepik.com/free-photos-vectors/ruller
1 sheet of cardboard for drawing : https://my-best.in.th/50634
1 roll of duct tape or pineapple fiber tape : https://www.wetapestore.com/th/filament-tape
1 sheet sticker : https://www.wetapestore.com/th/sticker-on-demand-laser-engrave-label-90-x-90-mm
Brushless motor No. No. 2814 1,500 kv : https://www.modelmotors.cz/product/detail/211/
???? Airfoil Naca 0015 : http://airfoiltools.com/airfoil/details?airfoil=naca0015-il
???? Airfoil Naca 0016 : https://carlpaton.github.io/2018/04/airfoils/

✅ Building a radio-controlled f3a or f3 A3 D is an easy RC model building for beginners. And for those who are new to RC model making, you can get detailed knowledge about RC models and how to make RC models here. You can make RC airplanes with foam. If you like watching this clip, let's DIY RC airplanes. Press to subscribe to the diy rc plane channel too so you won't miss the next clip.

✅ How to build a radio controlled f3a plane
Let's start with cardboard. Draw a plane and draw a design on the foam sheet. After that, use the foam cutter. Once we get the plane design, we polish the work piece with sandpaper. After that, let's make airplane wings.

✅ How to make the wings of f3a 3D rc airplane. After that we will use the hot wire to cut the foam. When we cut the foam into the shape of a radio controlled airplane. We also sanded with sandpaper. After polishing the workpiece with sandpaper, we take all the workpieces and the planes we prepared with water. Will use water to wash so that we can apply it. Next we will paint with stickers.

✅ Steps to make a detailed RC airplane, you can follow straight away where you use foam as a material to start, first you have to draw an airplane figure on the foam sheet first, after that you use a cutter to cut it out. Come and sand it with sand paper and in the pieces of the wings that we cut we can use glue to connect the two wings together.
And in the pieces of the wings that we cut we can use glue to connect the two wings together and you will have to harden them with carbon which we will embed the carbon in the wing of the aircraft. Airplane wings you need skill to make. We will use a cutter to gouge down the wings of the plane and place carbon rods inside the wings of the plane, which will make the wings of the plane very strong.

✅ 3D Aerobatics or 3D flying is a form of flying using flying aircraft to perform specific aerial maneuvers. They are usually performed when the aircraft had been intentionally placed in a stalled position.

✅ Introduction
In its most basic sense, 3D flight is controlled flight beyond the stalls critical angle of attack (AoA, or alpha) aka post-stall. Because the model is stalled and has little natural airflow across its flight surfaces, most 3D maneuvers require very large control deflections to vector the propeller thrust and change the models attitude.
✅ 3D aerobatic flying is a typically performed by model aircraft which have been configured with a higher thrust-to-weight ratio of more than 1:1. In fixed wing aeroplanes large control surfaces assist the aircraft on performing radical maneuvers which allow the aircraft to turn in tighter than conventional turns. This is achieved by having larger control surfaces; rudder, ailerons, and elevator and having greater amounts of throw applied to these control surfaces.

✅ Depending on the type of competition, a pilot may compete in Set Manoeuvres where a pilot can choose from a number of manoeuvres from pre-published set of moves or Freestyle, where pilots must show their skill within a predetermined environment in a free format. The Extreme Flight Championships (XFC) is a large international freestyle competition.

✅ Pilots often train moves using PC simulators such as RealFlight or other RC flight simulators. This allows the pilot to practice and hone their skills before using the real RC model which may be costly exercise in the event of a crash. Pilots have the ability to plug the controller used to fly the real model to the PC and simulator via a USB link cable thus giving the pilot a better response to the real world controls.

#flitetest #homemade #rc #f3a3d #rc3d #เครื่องบินบังคับ #howtomakercplane #rcairplane #airplane #buildrcplane