Coolest RC EVER - 3D Printed Eagle

Full Build Video: https://www.youtube.com/watch?v=5zrpbw0_7Oc
79in RC 3D Printed Eagle 1160g RTF

Thank you so much for watching!

If you like videos like this, consider buying me a coffee, it really supports me: https://www.buymeacoffee.com/troymcmi...​

See what else I am working on: https://www.instagram.com/troymcmilla...​
#3DPrinted​,#RCAirplane​, #ItFlies​

How to Print Thin Wall: https://www.youtube.com/watch?v=TZ_-A...​

STL Files: https://www.planeprint.com/eagle​

Products Mentioned:
Anycubic Mega X Printer: https://www.anycubic.com/products/meg...​
LW-PLA: https://colorfabb.com/lw-pla-natural​
White PLA: https://amzn.to/3ghcHl1​
Black TPU: https://amzn.to/2Sw3Oe8​
.030" clear Lexan sheet: https://amzn.to/3s4GSmv​
CA Glue: https://amzn.to/2J8EvNW​
CA Accelerator: https://amzn.to/3fpbycz​
2836 1120kv motor: https://amzn.to/30YhIKn​
30amp ESC: https: https://amzn.to/2OJ94gk​
3x HS-55 Servos: https://amzn.to/3oRnDKV​
1000mAh Battery: https://amzn.to/353cLmf​
AR620 Receiver: https://amzn.to/3j4PbK4​
DX6 Transmitter: https://amzn.to/3l6NFsD​
3pin wire assortment: https://amzn.to/3l1xNYt​
XT60 connector: https://amzn.to/3iyZWnf​
Y-Harness: https://amzn.to/3jAFwvo​
5mm magnet: https://amzn.to/35ZPLoN​
Lead weight: https://amzn.to/3cFnzeu​
Screw assortment: https://amzn.to/2SvMxSs​
2mm push rod ends: https://amzn.to/3nnjD4U​
Z-Bend pliers: https://amzn.to/34mA0rt​
Hobby Knife: https://amzn.to/3eYOYJq​
#11 blades: https://amzn.to/3vTJZ2W​
Hot knife: https://amzn.to/34AGOB1​
Drill Bits: https://amzn.to/3nIJzrx​
Build Mat: https://amzn.to/3vJmauw​
Carbon Rods: https://www.readymaderc.com​
Onboard Camera: https://amzn.to/3rp2OrH​



*These are the settings I used for my Anycubic Mega X 3D Printer with White PLA. These settings are not going to work with every printer, or every PLA. Printers have different length bodin tubes, and PLA’s have different melting points. These may not work exactly for you, but should give you a good base to start with if you have a similar size printer. Good luck!

LW-PLA
Temp 235c
Flow 55%
Retraction Distance – 2
Retraction Speed – 30
Retraction Extra Prime Amount – 0.3
All other settings the same as bellow:

Profile 3 Cura Settings:
Quality:
Layer Height – 0.25
Line Width – 0.4
Shell:
Wall Line Count – 1
Infill:
Infill Density – 0
Material:
Printing Temperature – 215
Build Plate Temperature – 60
Flow – 100
Speed:
Print Speed – 100
Outer Wall Speed – 35
Inner Wall Speed – 35
Travel Speed – 80
Travel:
Enable Retraction – Checked
Retraction Distance – 4
Retraction Speed – 30
Retraction Extra Prime Amount – 0.4
Combing Mode – off
Cooling:
Enable Print Cooling – Checked
Fan Speed – 80
Mesh Fixes:
Union Overlapping Volumes – NOT Checked
Special Modes:
Surface Mode – Surface
Experimental:
Slicing Tolerance – Middle






Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!